Go to previous page



The sensors for the parking aid system do not detect moving objects, such as children and animals, until they are dangerously close. Responsibility remains the driver's to drive with due care and attention during low speed maneuvers.


The sensors for the parking aid system may be externally influenced by hot exhaust gasses from nearby vehicles. The responsibility is the driver’s to drive with due care and attention during low speed maneuvers.


The sensors for parking aid system may not detect some obstructions. For example, narrow posts or small objects close to the ground. Objects above sensor level may not be detected, e.g., when approaching a flatbed truck the protruding part of the flatbed is not detected.


When washing the vehicle, do not aim high pressure water jet directly at any of the sensors. Do not use abrasive materials, or hard or sharp objects to clean the sensors. Only use approved vehicle shampoo.


Accessories that are fitted to the front or rear of the vehicle, particular care must be taken when using the parking aid. Accessories that are mounted in a position where it obstructs operation of a sensor or sensors will only detect the distance from the bumper to the accessory. The accessory then displays as an obstacle. Any obstacle beyond the detected accessory may not be indicated on the touch screen display.


The sensors must be kept clean to maintain accuracy and performance.


When a trailer is connected to a Jaguar Land Rover approved trailer socket, the rear parking sensors are disabled. When the trailer's electrical plug is not connected to the socket, or a non-approved towing system is fitted, the parking sensors do not operate as intended.


The 360° parking aid feature is not available in some markets.

  1. Parking aid button: Located next to the touch screen. Press to switch on. The switch LED illuminates. Press again to switch off.

  2. Parking aid sensor detection zones.

    Grey blocks indicate objects detected that do not pose a threat i.e not in a collision path with vehicle.

    Colored blocks indicate objects detected that pose collision threats.

  3. 360° parking aid sensor detection zones.

The parking aid system assists the driver while maneuvering the vehicle at low speed in confined spaces. When active, object tracking along the front, sides, and rear of the vehicle is displayed on the touch screen. The front, side, and outer rear sensors monitor a fixed distance around the vehicle. The inner rear sensors monitor a greater distance at the rear of the vehicle. The four side sensors provide the 360° parking aid monitoring along the vehicle's sides, creating a virtual detection zone.

The parking aid system can also detect low objects e.g., curbs in the front and rear detection zones and track them as the vehicle approaches even when they are no longer seen by the sensors.

While the vehicle is passing an object within its sensor range, the vehicle's integrated systems calculate its trajectory. The trajectory is displayed on the touch screen in the parking aid monitored area.

When a detected object is calculated to be a collision threat, it is displayed as colored blocks. The distance from a collision threat is color coded in a yellow to amber to a red scale, red being the closest. Other detected objects that are not a collision threat are displayed as grey blocks.


When the parking aid system is active, the system will only provide information of obstacles when a threat is detected.

A warning tone is given, which increases in speed as the vehicle approaches the object. The tone becomes continuous when the object is within 12 in (300 mm) of the vehicle. The warning tone will sound from the area in which a collision threat has been detected.

While the vehicle is stationary, the sensors for parking aid system do not detect objects or people approaching from the side. Also, at vehicle start-up, the vehicle has no sensor information about side objects or people. In both of these situations, ! is displayed on the touch screen in these virtual detection zones.


At vehicle start-up, the front sensors may not detect low objects, even if they were detected during the original parking maneuver.

To manually enable the parking aid system, press the parking aid button (1). The button illuminates while the parking aid system is enabled. Press the button again to disable. The LED extinguishes.

The parking aid system also activates when the following is selected:

  • Reverse (R) or Neutral (N) is selected on vehicles with automatic transmissions.

  • Reverse (R) is selected on vehicles with manual transmissions.

The parking aid system can be set to activate automatically for when:

  • The vehicle’s speed falls below 6 mph (10 km/h).

  • Drive (D) is selected for vehicles with an automatic transmission.

  • Reverse (R) is selected for vehicles with a manual transmission.

To enable the auto on feature, on the touch screen select, the Settings icon to access the PARKING AID SETTINGS pop-up menu. Select Automatic PDC ON.